CHUQY. CHANGE EASY.
Change your motorbike wheel fast. Spend more time on the road.
CHUQY. CHANGE EASY.
Change your motorbike wheel fast. Spend more time on the road.
– Easiest wheel changing device EVER
– Axle slides out easily as Chuqy holds the weight of the wheel
– Reduces frustration (and swearing)
Double sided swing arm only. Max tyre width 210mm.
Gap between floor and tyre must be 10-130mm when on a bike stand.
I have one and it's a real time saver, on GSXR 1000. Lining the back caliper up is a pain without one of these
- Darren G.
I can't wait to get mine. I put
tyres on a customer's XTZ660
the other day and it took me
10 minutes to get the wheel
back on. I don't have three hands!
- Collin B. from Ridewithme
The easiest, most stress free,
simple and FAST tyre change
I've ever done. Well done
for inventing something so
fantastic
- Melinda H. from iRIDE WA
I have one and it’s a real time saver, on GSXR 1000. Lining the back caliper up is a pain without one of these
– Darren G.
I can’t wait to get mine. I put tyres on a customer’s XTZ660 the other day and it took me 10 minutes to get the wheel back on. I don’t have three hands!
– Colin B. from Ridewithme
The easiest, most stress free, simple and FAST tyre change I’ve ever done. Well done for inventing something so fantastic
– Melinda H. from iRIDE WA
THE EASIEST WHEEL
CHANGING DEVICE EVER
STEP 1
Get your bike up on a stand.
STEP 2
Chuck Chuqy Underneath.
STEP 3
Adjust to the right height and width.
STEP 4
Remove the wheel.
STEP 5
Savour the moment.
Step 1
Get your bike up on a stand.
Step 2
Chuck Chuqy Underneath.
Step 3
Adjust to the right height and width.
Step 4
Remove the wheel.
Step 5
Savour the moment.
FAQS
How much does Chuqy cost?
$99.99 AUD – postively bargain price!
Will Chuqy work as a bike stand?
No, Chuqy is not designed to hold the weight of your bike!
Will Chuqy work on any motorcycle?
Chuqy is designed for use on dual sided swing-arm bikes. Double sided swing arm only. Max tyre width 210mm.
The gap between the wheel and the ground, when the bike is on the stand, must be 10mm-130mm.
The vertical rods don't drop without dragging them down when I push the quick release button.
Slide the vertical rod out, and re-insert upside down. With the manufacturing process the vertical tube that the rod fits into is slightly tapered (it’s called a draft), if you put in the ‘wrong’ way it’s tight, put in the other way and it’s correct. Yes we should have marked top and bottom and moving forward, we will – sorry!
I've lost one of the thumb nuts.
We sell a set of replacement thumb nuts, go to the website and we’ll post them to you.
The horizontal rods are too wide and it doesn't fit between the stand legs.
You can cut the horizontal rod to fit, just make sure you measure carefully and don’t cut too much off.
Will Chuqy work on my front?
Yes it will, set up Chuqy in exactly the same way as for the rear, remove calipers and axle, then lower Chuqy using the quick release buttons before sliding out. When refitting, slide Chuqy in between the forks, then raise using quick release as high as you can get, then use the screw motions of the vertical rods to align the axle.
CHANGE EASY
– Stop balancing your wheel with wooden blocks
– Adjustable to exact height to change your wheel
– Comes with instructional video
